검색결과 리스트
글
OSNAP(Object Snap)
Osnap은 좌표 값을 모르거나 구성선을 그리지 않아도 대상물의 특정 위치를 빠르고 쉽게 찾아주는 기능으로 정확한 도면 작업을 위하여 자주 활용된다. 단독으로 쓰이지 않고종속 명령으로 사용하는 기하학적 좌표 값이다.
▷ 키보드의 Ctrl키를 누른 채로 마우스의 오른쪽 버튼을 클릭하면 화면의 크로스 헤어 위
치에 오스냅의 단축메뉴가 나타난다.
▷ Toolbars 대화상자에서 Object snap 도구 막대 아이콘을 불러내 사용한다.
▷ 직접 키보드로 입력한다. 이때 Osnap 명령의 앞 세 글자만 입력하면 된다.
▷ Osnap을 사용할 때 아래 그림에서와 같이 선택박스로 지정하면 표식기와 풍선 도움말
을 보여준다.
객체스냅의 사용 예
객체스냅에서 옵션들의 용도 및 도구막대, 단축 키
객체스냅옵션 |
용도 |
도구막대 |
단축명령 |
Temporary track point |
임시 추적점 |
|
TT |
From |
임시 참조점 |
|
FRO |
Endpoint |
끝점 |
|
END |
Midpoint |
중간점 |
|
MID |
Center |
중심점 |
|
CEN |
Node |
포인트 점 |
|
NOD |
Quadrant |
사분점 |
|
QUA |
Intersection |
교차점 |
|
INT |
Extention |
연장 교차점 |
|
EXT |
Insertion |
삽입점 |
|
INS |
Perpendicular |
수직점 |
|
PER |
Tangent |
접선 |
|
TAN |
Nearest |
근처점 |
|
NEA |
Apparent Intersection |
가상 교차점 |
|
APP |
Parallel |
평행 |
|
PAR |
None |
취소 |
|
NON |
Osnap Settings |
설정 |
|
DS |
(1)From에 의한 임시 참조점 확립
시작 객체 스냅은 다음점을 지정하기 위한 기준점으로 임시 참조점을 확립할 수 있다. 확
립된 임시 참조점에서 상대 좌표를 입력하므로 시작점을 위치시킨다.
Command : c
CIRCLE Specify center point for circle or [3P/2P/Ttr(tan tan radius)] : from
Base point : end of (p1점 지정)
of<Offset> : @50,-50
Specify radius of circle or [Diameter] <10.0000> : 30
From에 의한 임시 참조점의 확립
(2)Endpoint에 의한 끝점 연결하기
Command : line
LINE Specify first point : end
of (p1점 지정)
Specify next point or 〔Undo 〕: end
of (p2점 지정)
Specify next point or 〔Undo 〕:
Command :
LINE Specify first point : end
of (p3점 지정)
Specify next point or 〔Undo 〕: end
of (p4점 지정)
Specify next point or 〔Undo 〕:
Endpoint에 의한 끝점 연결
(3)Midpoint, Nearest 및 Perpendicular 사용하기
Command :
LINE Specify first point : mid
of (p1점 지정)
Specify next point or 〔Undo 〕: mid
of (p2점 지정)
Specify next point or 〔Undo 〕:
Command :
LINE Specify first point : nea
of (p3점 지정)
Specify next point or 〔Undo 〕: per
of (p4점 지정)
Specify next point or 〔Undo 〕:
Midpoint, Nearest 및 Perpendicular 사용
(4)Intersection에 의한 교차점에 원 그리기
Command : c
CIRCLE Specify center point for circle or 〔3P/2P/Ttr(tan tan radius) 〕: int of (p1점 지정)
Specify radius of circle or 〔Diameter 〕: 20
Command : l
LINE Specify first point : int of (p2점 지정)
Specify next point or 〔Undo 〕: int of (p3점 지정)
Specify next point or 〔Undo 〕: int of (p4점 지정)
Specify next point or 〔Close/Undo 〕: int of (p5점 지정)
Specify next point or 〔Close/Undo 〕: c
Intersection의 사용
(5)Tangent에 의한 접선 그리기
Command : l
LINE Specify first point : tan to (p1점 지정)
Specify next point or 〔Undo 〕: tan to (p2점 지정)
Specify next point or 〔Undo 〕:
Command :
LINE Specify first point : tan to (p3점 지정)
Specify next point or 〔Undo 〕: tan to (p4점 지정)
Specify next point or 〔Undo 〕:
Tangent에 의한 접선의 작성
(6)Quadrant에 의한 원의 사분점 지정
Command : l
LINE Specify first point : qua to (p1점 지정)
Specify next point or 〔Undo 〕: qua to (p2점 지정)
Specify next point or 〔Undo 〕: qua to (p3점 지정)
Specify next point or 〔Close/Undo 〕: c
Quadrant에 의한 사분점
(7)두 선의 Apparent Intersection(확장가상 교차점에) 원그리기
Command : c
CIRCLE Specify center point for circle or 〔3P/2P/Ttr(tan tan radius) 〕: app
of (p1 지정) and (p2 지정) - 윈도우창을 p2에 접근시키면 교차점 표식기와 툴팁을
보여준다. 이때 클릭한다.
Specify radius of circle or 〔Diameter 〕<20.0000> : end of (p3 지정)
Apparent Intersection에 의한 가상 교차점 사용
(8)ApparentIntersection(확장 가상 교차점의) 사용
Command : l
Line Specify first point : app
of (p1점 지정) and (p2점 지정)
Specify next point or 〔Undo 〕: per to(p3점지정)
Specify next point or 〔Undo 〕:
1단계 2단계 3단계 결과
(9)Extention(연장선을) 사용한 연장선상에 스냅하기
Command : circle
Specify center point for circle or[3P/2P/Ttr(tan tan radius)] : ext
of (선택박스를 p1점에 접근시켜 풍선 도움말이 나타나면 우측으로 끌기 이동하여
연장선을 하이라이트 시킨다.) 30
Specify radius of circle or[Diameter] <30.0000> : 30
Extention을 사용한 연장선상의 스냅
(10) Point Filter에 의한 Osnap
점을 지정할때 xy 좌표값 중 어느 하나의 좌표값은 이웃 객체에서 Osnap으로 취하고 다
른 하나의 좌표값만 입력하여 점을 구성한다.
Command : c CIRCLE Specify center point for circle or 〔3P/2P/Ttr(tan tan radius) 〕: .y of mid - y 좌표값으로 중간점을 지정하기 위하여 입력
of (p1점 지정) of (need XZ) : p2점 지정 Specify radius of circle or 〔Diameter 〕: .y of int of (p3점 지정)
of (need XZ) : <Ortho on> p4점 지정 - 직교모드를 사용한다.. Command : CIRCLE Specify center point for circle or 〔3P/2P/Ttr(tan tan radius) 〕: cen
of (p5점 지정) Specify radius of circle or 〔Diameter 〕: .y of end of (p6점 지정)
of (need XZ) : <Orthoon> p7점 지정 - 직교모드를 사용한다.
Point Filter에 의한 스냅
'[AutoCAD명령어] > AutoCAD[200X]' 카테고리의 다른 글
AutoCAD 명령어 정리 - INSERT(블록 삽입) (0) | 2012.12.31 |
---|---|
AutoCAD 명령어 정리 - BLOCK(블록) 정의하기 (0) | 2012.12.31 |
AutoCAD 명령어 정리 - 객체 특성 도구막대 사용하기 (0) | 2012.12.30 |
AutoCAD 명령어 정리 - Tracking(추적) 사용하기 (0) | 2012.12.30 |
AutoCAD 명령어 정리 - AutoSnap(자동스냅) (0) | 2012.12.30 |
AutoCAD 명령어 정리 - ARC(원호 그리기) (0) | 2012.12.30 |
AutoCAD 명령어 정리 - CIRCLE(원그리기) (0) | 2012.12.29 |
AutoCAD 명령어 정리 - PICKBOX의 크기 조절 (0) | 2012.12.29 |
AutoCAD 명령어 정리 - ERASE(지우기) (0) | 2012.12.29 |
AutoCAD 명령어 정리 - LINE(선 그리기) (0) | 2012.12.29 |
RECENT COMMENT